Results 1 to 10 of 21
Thread: Brake fluid flush
06-14-2012, 09:26 PM #1
Brake fluid flush
How often do you guys change the brake fluid?
The brake fluid on my burb is getting dark. I plan to suck out the dirty fluid off the reservoir first then fill it up with fresh fluid then bleed manually using the 2-man brake pedal pumping and wheel caliper bleeder opening procedure. First time after 160k miles. Anymore steps i missed out?2011 Chevy Silverado LT 4WD 30k miles
2001 Suburban 2WD, 5.3, V8 185k miles
06-15-2012, 12:28 AM #2
A brake fluid flush is best done by a machine. This will do a much better job of cleaning all lines and eliminating any contaamination. it is fairly inexpensive at most brake shops2010 Chevy Silverado Z71 ext cab.4x4
72 Monte Carlo 350-415 hp- sold (June 2011) to pay medical bills
79 Impala 350 4bbl 375 hp- sold (June 2011)to pay medical bills
"If He asks you to go a mile go two"
06-15-2012, 01:31 AM #3
Coach is right, but your interval is dictated by use, and quality of fluid. Normally, the fluid only changes color due to high heat, like when the calipers get really hot. Normally when replacing parts, enough fluid is lost and replaced to keep things rolling along well enough. Sometimes however, and sooner or later things happen, and it's time for a complete flush. The biggest problem I ever experienced with brake service, is getting the bleeder valves open. Ofter I have had to replace calipers and rear wheel cylinders due to this issue. I found the using a small drill bit in a pair of pliers to clear out the holes, and wire brushing and spreaying the outsides with PB Blaster or WD40 for three days, twice a day, and using a six point socket, did the trick.
Brian Larson CST. KC9DAK.
87 GMC G20 6.2 diesel.
06-15-2012, 07:12 AM #4
I hate shops @#*ing up my ride. I would rather do the work that don't require special tools and equipment. I am only talking about replacing the old fluid and nothing more. The burb has never seen snow or salted roads and I don't anticipate siezed bleeder or stuck calipers. Besides, I plan on involving the wife. Thanks.
06-15-2012, 07:20 AM #5
Well with 160k miles, I thought it won't hurt to do a flush and besides the fluid is dark. PB blaster is a good idea to soak the bleeders a day before the flush. I have fitting wrenches and small six point wrenches for the bleeder. I don't anticipate siezed or rusted bleeders since the vehicle spent most of it's life in southeast. I already looked at the bleeders and they are clean.
Will the flush also take care of the old fluid in the ABS pump?
06-15-2012, 09:21 AM #6
I don't know about the ABS pump, all I can say there is once you bleed what you can out of the system manually, fire the truck up and depress the pedal with the rear brake valves open, and see if you get clean or dark fluid. You will have to rebleed them manually after that. Is the pump before the master cylinder or after it? I recommend a vacume pump, you can get at autozone for arround $50. It makes the bleeding job, a one man chore, and reduces spillage to nothing. I have one, and my only complaint is the bottle isn't big enough for my needs. But I just empty it and keep going. Anybody with two hands wouldn't have an issue with that, but as I only have one arm, I'm gonna gripe! I've been the pedal man, and the wrench man so often it aint funny, so I feel your need. Good luck, and please let us know how it went.
06-15-2012, 09:24 AM #7
I have always just done a gravity bleed on my trucks. I just open all the bleeders and keep filling the the reservoir until the fluid comes out clean. No, this does not get out all the contamination like a brake shop would, but it does replace all the fluid. In a jam (hard to get help around here sometimes) I have used the bleeder screws with a check valve. You can pump your brakes and it will shoot fluid out but not let air in. My neighbor does his every year. He uses a cheap vacuum bleeder that he bought at harbor freight. It seems to work well.
1995 Silverado 4x4
6" BDS Suspension Lift-3" Body Lift-Add A Leaf in rear -Trailmaster SSV Shocks-Duel Steering Stabilizer Kit -AirAid Cold air intake-
4.56 Gears with Detroit Auburn Locker-Pro-Comp Traction Bars with duel shocks-Aluminum Skid Plate Kit-38.5" x 16.5" Mickey Thompson Baja Claws-Constant Dropping fuel gauge
2005 Yukon XL Jet Power Programmer, Bilstein Shocks, Bilstein rear springs, Helwig Anti-sway bars, EGR Window Visors, EGR Hood Shield, Denali Headlights, Headlight harness upgrade, GE NightHawk Bulbs, White Night Rear lighting system, Russell Braided SS brake lines, PowerStop Brake pads, PowerStop cross drilled and Slotted Rotors, http://www.gmtruckclub.com/forum/sho...5-GMC-Yukon-XL
2002 Silverado ext cab 2wd (Sold)
2003 Yukon XL (Totaled)
06-15-2012, 09:47 AM #8
Do I do the closest caliper first then the farthest last?
06-15-2012, 10:04 AM #9
As long as the reservoir is full you will not have to worry about air. I just open all four and let it start running out. The bleeder with the check valve speeds the process, you can force the fluid thru instead of letting it drip out. As far as the order goes, I have no idea what the proper order would be. If you are not bleeding air out I don't think that it should really matter.
06-15-2012, 11:14 AM #10
- Join Date
- Mar 2007
- Grand Prairie, Texas
- Blog Entries
Harbor freight sells their brake bleeder for $30 it does a great job.
Motive also sells a real good vacuume bleeder that has a resevoir to fit on top of your existing resevoir so you dont run out of fluid while drawing down, it's designed to be used when doing fluid changes.
By AzDragonLord in forum Maintenance & UpkeepReplies: 6Last: 06-28-2011, 06:58 PM
By mvoss2576 in forum Maintenance & UpkeepReplies: 18Last: 11-24-2010, 10:17 PM
By ridick_bowen in forum Lifted & Offroad SuspensionReplies: 1Last: 11-04-2010, 12:52 PM
By vms4evr in forum Maintenance & UpkeepReplies: 1Last: 09-27-2010, 03:09 PM
By dflahe in forum Chevy Silverado Forum (GMC Sierra)Replies: 1Last: 09-11-2007, 11:23 PM
Tags for this Thread