GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 6 of 6
  1. #1

    Default Wiring an old truck. HELP NEEDED!!

    A good friend of mine has an old Kiaser weapons truck. An M 715. It has a 427 and I think a NV4500 tranny. It is his toy. He is in the Navy and currently unable to work on his truck. His wife is taking the truck to a body shop to have the rust,holes and other issues on the body fixed. Than it will be painted flat black. But the wiring in the truck is sad to be polite about it. I would like to try to rewire it for him while he is gone. That way when he gets back we can have some fun in it. The truck is basic as far as what needs to be wired. The only exception is he installed an electrcic fan, but not thermal switch. So after the truck is started and ran for a few minutes you have to manually flip the switch for the fan, and conversly when you shut the truck off you have to remember to flip off the fan switch. So I know I need some kind of relay to fix that issue. But my question is what is the best way of redoing the rest of the wiring in the truck? A premade harness or make one up? Any help would be appreciated!





    2011 GMC Sierra SLE - 5.3 - 4X4 - Z71 - King Shock Level Kit - Body Color GMC grill emblem - 2 Tone Engine Cover, Rad Cover and Battery Box - Volant CAI - Tru Cool 40K tranny cooler - Sylvania ZXE bulbs Hi/Low -TriFold Hard Tonneau Cover- CoverCraft Seat Covers - Diablo inTune - GoRecon LED under rail lights - GoRecon LED White Lightning Tailgate Light Bar - Windows tinted to 45%- Kenwood DNX6990 - JL Audio C5-650 &650X- JL Audio Amp- Interco Truxus M/T 33x12.50x18

  2. #2

    Default

    NOS wiring harnesses for that truck should still be available from surplus dealers. You should also download and read the Technical Manuals (TMs) for it. The TM is very complete and has complete wiring diagrams with every bit of info imaginable on them. It appears m715zone.com may have the TMs on the site, but you have to register for a free account. Make sure you get all the manuals. There should be a manual that ends in -10, -20, and probably -34. The bigger the number, the more in-depth the information.
    Christopher

    1991 Chevy Suburban 1/2 ton 2WD w/ chevy SBC 350-3/4 ton drivetrain upgrade w/4.10 gears 200K miles
    2005 Saturn ION-2 Stock 277K miles
    1982 Bronco, 1993 Bronco (sold), 1971 M35A2 Deuce and a Half



    There are 10 kinds of people, those who understand binary, and those who dont...

    Remember kids, the only difference between screwing around and science is writing it down- Adam Savage

  3. #3
    Former Member
    Join Date
    Apr 2012
    Location
    Reading, PA
    Posts
    291

    Default

    Quote Originally Posted by Crawdaddy View Post
    NOS wiring harnesses for that truck should still be available from surplus dealers.

    Keep in mind that wiring, even though NOS; is still almost 50 years old at this point (hey, the 60s were a long time ago). Since nothing else is apparently stock (a 427 and NV4500 were not optional equipment on the M715!), I would source the end connectors and new wire, and make my own harnesses. Chances are, you will end up replacing some of the switches and other components too.

    I have an M37 sitting at the house, that's the route I will take when the time comes.

  4. #4

    Default

    When I re-wired my 1960 Land Rover, my dad and I stripped all the wiring out and went through and made it all new. some of the wiring had been messed with before so it was kind of a mess and we felt it was the best way to clean it up. We bought a few sets of fuse blocks (I think it originally had like 2 fuses). We had also converted it from positive ground (generator) to negative ground (alternator) years before as well as electric fuel pump rather than mechanical.
    David
    2004 Silverado 2500 Crew Cab 4x4, AMSOIL EA air filter, Granatelli MAF sensor, Throttle body spacer, Magnaflow exhaust (true dual to 2 in 1 out muffler), 6" ProComp lift (add a leaf and 5" superlift rear block), Bilstein shocks, 35's (Cooper Disoverer ST) and 4.10 gears, Rhino Liner, EGRUSA fender Flares and widow visors, extended stainless steel brake lines, firestone airbags w/onboard air compressor, Pioneer Avic X940BT navigation, Accel backup camera.
    http://www.gmtruckclub.com/forum/sho...Silverado-2500
    1960 Land Rover Series II 88
    2001 Pontiac Sunfire
    2013 Toyota Avalon Limited (Wife's Car)
    NRA Life Member

  5. #5

    Default

    ints not the best picture and we actually added a bit of wiring and used 12-14 guage for alot of stuff but it shows the fuses and relay blocks
    Click image for larger version. 

Name:	LR06.jpg 
Views:	117 
Size:	80.7 KB 
ID:	41447

  6. #6

    Default

    I was searching around last night on the website that @Crawdaddy recommended and found some of those members used a harness kit from EZ wire. It is a 12 circuit harness complete with fuce block and the wires are marked every 12 inches or so for $185. I am strongly leaning that way. It should make the job easier for me and also should be a cleaner look. The easier part is important to me since the truck is in VA and I am in NC. Thanks to all for your input.

Similar Threads

  1. Wiring info needed
    By Quad racer#212 in forum GM Electrical Tech
    Replies: 5
    Last: 05-21-2013, 07:25 PM
  2. 1987 Motor wiring diagram needed
    By love_nikki_6 in forum GM Powertrain
    Replies: 1
    Last: 03-27-2011, 01:58 PM
  3. Wiring diagram needed OBD2 to OBD1
    By shawnlesky in forum General Chevy & GM Tech Questions
    Replies: 1
    Last: 12-24-2010, 10:45 PM
  4. 74 Sub Wiring Help Needed
    By joemud in forum Audio, Video & Gadget Tech
    Replies: 4
    Last: 10-04-2008, 03:12 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •