Results 11 to 16 of 16
Thread: cleaning engine bay
08-08-2012, 03:17 AM #11
I just want to jump in here and caution anyone who uses a pressure washer to clean their engine - at least for those of us with the V8s anyway. I always assumed that as long as I kept the pressure away so that nothing was directly blasted, it wouldn't cause any problems. BUT, I rinsed my engine bay with a pressure washer on Thursday, and on Sunday I got a check engine light for a defective knock sensor. My research since then shows that apparently when you get that much water in there, it can sit below the intake manifold and corrode the knock sensors. A lot of the cases of bad knock sensors (P0332 code - only the rear knock sensor ever seems to get water damage) seem to happen a couple of days after the engine bay is washed. Sometimes it goes away, sometimes it doesn't. If my problem doesn't go away once its had a chance to dry, I'll have to replace both knock sensors and the wiring harness because I don't want to have to remove the intake again if the other one fails. The cost in that case would be about $200-$250 plus about 3 hours worth of labor... that adds up to about $500 or more total if you have a shop do it (at least in my area).
Anyway, after all that, what I'm trying to say is just be sure to wash your engine bay carefully.
2001 Silverado Reg. Cab Not-So-Base -- SOLD
2003 Avalanche Z71. No Cladding. Check out my Mod thread.
1974 Triumph Spitfire 1500 - Work in Progress
2003 Sierra 3500 Duramax. The Newer, Better Work Truck
08-09-2012, 12:42 AM #12
well it sounds alot like some guys should do a nice how to, or DO and DONT section on this topic LOL
might benefit alot of people2000 Chevrolet Silverado
4.3L V6, 4L60E, 2WD, Single Cab
Poweraid TB Spacer
Flowmaster 10-series exhaust (dumped)
Edge CS insight monitor
LS-1 Dual Electric fans
Corvette tranny servo swap
Head Unit: Alpine
Speakers: Alpine SPR-60C 6.5" component set, 4X6 Infinity Kappas
Subs: 2-12" Kicker CVT's
Amps: Alpine-M1000 (subs), Alpine MRX-F65 (Speakers)
305/70R16 NITTO Terra Grapplers
16" PROCOMP 7089's
2" leveling kit
3" Fabtech Spindle Lift Kit
Front/Rear-Bilstein 5100 shocks
35W HID Low Beams
RECON LED smoked roof cab lights
HELLA LED taillights and 3rd brakelight
HELLA FF-75 Aux. Reverse Lamps
RIGID dually D2, flush mount, wide beam
Hawk HPS Brake pads
Russell braided steel brake lines
Powerstop-red powdercoated brake calipers
Powerslot Cryo brake rotors
EGR in-channel window visors
08-31-2012, 09:36 PM #13
okay so i just sprayed out my engine bay....
i used skippys method, seems to have been good so far, started up and didnt die...
however, ill use simple green and rags once i replace my fuel injectors to get down to the finer cleanliness...
quick question... i know this aint the right thread but...
ive had some misfiring problems for a few weeks, only on cold starts, and goes away once the engine is hot, but i noticed that after doing this engine wash and driving home then, to and from an autoparts store, it seems to have amplified the stumbling/misfiring. made it misfire while my engine was actually hot...
so are fingers pointing more towards ignition caused misfiring now??? since being wet seems to have done this?
09-01-2012, 12:51 PM #14
When was the last time you changed plugs, and did you double check the gapping on them? Over time, the plugs' gaps will widen due to wear, takes a lot of voltage to cross that gap and a few misfires only amplify that due to fouling. I'd check plugs first, then check your fuel injectors. To determine if your injectors are firing, just hold a screwdriver against them (metal end on the injector) and the handle against your hear, you'll hear the tick tick tick from the pulsing if it's firing consistently.
Beyond that, check your fuel pressure, and replace your fuel filter, if you've got one and haven't already done so.
-Skippy.2006 Vortec Max 1500
-Custom Tune (389HP 440 Ft/lbs Trq - Dyno'd) | Volant CAI | Magnaflow Dual-in/out Exhaust w/3" stainless pipe tips | Fully Built Transmission w/ Red Eagle Clutches & Kolene Steels w/ Corvette Servos and Stage2 Shift Kit | 35K Tranny Cooler | Mobil 1 | Royal Purple Rear Diff
-Spray-in Bed Liner
-Premium Sound w/lifetime Satellite Radio | Leather | Sunroof | Heated Seats
-Limbstriping from USING the truck (those are badges of honor)
09-01-2012, 07:46 PM #15
yes, i did those some time back, i actually created a thread about it on here recently, i was just too lazy to pop it up real quick, but nothing ignition I know of, but i will be replacing my injectors whenever they get here
09-01-2012, 08:17 PM #16
Good way to test plugs and gaps, start truck, put foot on brake and gas (power brake). Apply small amount of load, if you have a plug issue, wire, plug, gap, you should here small popping and missing instead of a nice consistent groan.
By LOVINTHESTORM in forum Detailing & Truck CareReplies: 3Last Post: 05-10-2012, 10:35 PM
By Big_Ben in forum Maintenance & UpkeepReplies: 1Last Post: 03-14-2012, 09:11 PM
By bluebrick in forum Chevy Truck TalkReplies: 3Last Post: 02-02-2012, 12:18 AM
By ace08 in forum General Chevy & GM Tech QuestionsReplies: 4Last Post: 03-08-2010, 05:29 PM
By Prophet1990 in forum Chevy Truck AccessoriesReplies: 12Last Post: 01-05-2010, 12:37 PM