GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Results 1 to 9 of 9
  1. #1

    Default Cylinder resleeving Question

    I want to know if it is possible to resleeve a cylinder on a 4 Cylinder block?

    Because my number one cylinder looks like it has a hair line crack in it but i i'm not sure yet but i'm goin to have it checked to be on the safe side.

    Any info would be gratefully Appreciated
    Proud Member Of Anderson County Coon Club

    Keep them Treed Boys

    Own and Drive a 1985 Chevy S10 2.5L 4 Speed

  2. #2

    Default

    The "Iron Duke", this I4 engine has an iron block; and, I think the addition of a sleeve is normal repair for this engine (of course, that depends upon the size of the crack you are trying to fix.

    The sleeve needs to go in from the deck (top of block) and is held in place with a grove cut into the top of the bore
    Ray

    '09 Avalanche LTZ - Black
    '05 Envoy XL (sold)

  3. #3

    Default

    it's just a hair line crack about middle way's in the number 1 cylinder. and I'm worried that is where the water is getting in to my oil at but i'm not sure unless i can find someone to test and see how bad the crack is.

  4. #4

    Default

    It's possible to do, I havent heard of a shop that does this type work in a long time, its not economical to do any more most shops just replace the block.
    But I'm sure if you spend a little time searching you'll find a quality shop that can do the job.
    In one of its old versions that engine block was sleeved from the factory to cut down the displacement, dont remember what vehicle it was used on anymore though.

  5. #5

    Default

    yeah i been searching the internet and haven't found a shop yet to do it. But I'll keep searching and i might find one if not I'll go to pull a part and pull the best looking block out of a junker.

  6. #6

    Default

    Here is some pictures of the crack in the number cylinder. it's just a hair line crack but it's got me puzzled how it got there. i cleaned it best i could with a wire brush on a drill.

    Click image for larger version. 

Name:	cylinder crack 001.jpg 
Views:	74 
Size:	42.2 KB 
ID:	43119
    Click image for larger version. 

Name:	cylinder crack 002.jpg 
Views:	72 
Size:	46.5 KB 
ID:	43120
    Click image for larger version. 

Name:	cylinder crack 003.jpg 
Views:	71 
Size:	45.3 KB 
ID:	43121

  7. #7

    Default

    Most shops don't wanna mess with a cracked block any more. It's to labor intensive, meaning expensive, to do. Especially when there clean, rebuildable blocks littering wreaking yards all over the country.

    97 Chevrolet Suburban K1500 5.7L
    78 GMC High Sierra K1500
    Fat, drunk, and stupid is no way to go thru life.

  8. #8

    Default

    That's definitely a crack. If I were you, I'd start looking for a junk yard engine and replace that block.
    Good Luck and God Bless
    Remember that if you're not part of the solution, then you're part of the problem!

  9. #9

    Default

    well every junk yard i called or went to they don't have one. and Trust me i been to pretty close to 150 junk yards in Tennessee and still haven't found one yet. and when i do find one it was either had a busted block or a slung rod. but anyway i found a place in Maryville Tn that does resleeving for 75.00 to a 100.00 and that's bead blasting it clean and everything.
    Last edited by 85 S10 Man; 08-23-2012 at 09:48 PM.

Similar Threads

  1. What's Your Cylinder Index??
    By Sierraowner5.3 in forum The Coffee Shop ~ Chit Chat
    Replies: 19
    Last: 04-06-2012, 11:01 AM
  2. 07 Silverado 4 to 8 cylinder?
    By drillbit26 in forum Chevy Silverado Forum (GMC Sierra)
    Replies: 5
    Last: 11-23-2010, 05:07 PM
  3. Where's Cylinder #7
    By hblock72 in forum GM Powertrain
    Replies: 1
    Last: 10-23-2009, 01:28 PM
  4. compression a little low on 1 cylinder
    By jetjarv in forum GM Powertrain
    Replies: 2
    Last: 06-22-2009, 12:17 PM
  5. Hello and ignition cylinder question
    By mbailey5947 in forum Chevy C/K Truck Forum
    Replies: 5
    Last: 02-18-2009, 08:28 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •