Results 11 to 20 of 26
Thread: Reduce rear sag when towing?
08-24-2012, 10:16 PM #11
the RAS seems pretty cool too (and not much more than the airbags), but since I have experience with the airbags I will say they are great. I also say that Firestone (firestone industrial not the tire firestone) makes a better bag than airride when I was looking for mine. I really like the firestones on my truck and simple to install.
2004 Silverado 2500 Crew Cab 4x4, AMSOIL EA air filter, Granatelli MAF sensor, Throttle body spacer, Magnaflow exhaust (true dual to 2 in 1 out muffler), 6" ProComp lift (add a leaf and 5" superlift rear block), Bilstein shocks, 35's (Cooper Disoverer ST) and 4.10 gears, Rhino Liner, EGRUSA fender Flares and widow visors, extended stainless steel brake lines, firestone airbags w/onboard air compressor, Pioneer Avic X940BT navigation, Accel backup camera.
1960 Land Rover Series II 88
2001 Pontiac Sunfire
2013 Toyota Avalon Limited (Wife's Car)
NRA Life Member
08-24-2012, 11:13 PM #12
- Join Date
- Mar 2006
- Cameron, NC
- Blog Entries
The cool part about the roadmasters is that they install in 5 minutes and come with a 100% satisfaction guarantee. If, in the first 30 days you decide it isn't the best thing you ever bought for your truck, they will give you your money back with no questions asked. That is a pretty solid guarantee! Call Ryan at Roadmaster and at least chat with him before you decide.
Air bags are cool and I am not bashing them on any level, but to install them, you have to mount a compressor, run air lines, wire it all up... Maybe even do some fabrication. You have to manually adjust them unless you install a self-leveling system and they take a bit of time to inflate. The RM self adjusts instantly to changing road conditions and load. It's operation is completely transparent and you will never know it is there, aside from the greatly improved ride... even unloaded. It installs with only 2 bolts per side and without having to take ANYTHING off of your truck to install it (unless you want to take the tire off to make the front nut and bolt easier to access.) In any case, Give Ryan a call! He is absolutely a no-pressure kind of guy. (704) 523-2638. If you get his voicemail, DO leave a message... He WILL call you back!
I have pressured you more than he will! LOL! I do not work for the company and have nothing to gain either way! I am just passionate about these.
Last edited by moogvo; 08-24-2012 at 11:16 PM."It went together didn't it? Well then there has to be a way to take it apart!" - Me.
Check out my image gallery HERE.
"The true measure of a man is how he treats someone who can do him absolutely no good." ~Samuel Johnson (1709-1784)
08-24-2012, 11:34 PM #13
Moogvo is spot-on about the installation being simple. Unload the rear axle, remove the tires, bolt the new units into place, tension the units, replace the tires, and re-load the rear axle. That's it.
This installation is 47.5% prep work, 47.5% post-install work, and 5% actual installation. It took me 2 hours from start to finish ... and that was only because I have locking lugs (for every lug!) that are a complete pain in the butt to put on/off and, the work was being done in a shop that wasn't mine, only hand tools were used, and I was photographing things and making notes.
The actual RAS portion of the installation took ~6-7 mins from emplacement to completion of tensioning. If my truck wasn't lifted, if I had normal lugs and wheels, and if I had been doing this in the shop I normally work in without any photos, I could have done the installation in ~45 mins from start to finish. Add in some air tools instead of hand tools and I'd dare say it's a 30 min job...
I should also add that there's very little to go wrong here -- compared to air bags which have a lot that can go wrong (from comprssor to air lines to wiring to the bags, themselves). Also, the need for the compressor, lines, potentially a larger alternator to run the compressor if yours is insufficient, etc -- are potentially hidden costs to air bags that the RAS doesn't have.
Oh, and if it matters for some, the RAS is 100% made in USA. It's an operation out of Charlotte, NC...
Last edited by SurrealOne; 08-24-2012 at 11:39 PM.
08-24-2012, 11:43 PM #14
- Join Date
- Mar 2006
- Cameron, NC
- Blog Entries
I think they should hire us, Surreal!
08-26-2012, 10:33 AM #15
Ahhh there's so many good reviews hard to choose one!
"Never ask a man if he's from Texas. If he is, he'll tell you. If he isn't, there is no need to embarrass him."
2012 Silverado 1500 Texas Edition 4x4 LT skid plate, 5000k 55W low beams with DRL fuse removed, 5000k 35W fog lamps.
Leveling kit and tires coming soon.
Leaving for boot camp at MCRDSD 20121008.
08-26-2012, 11:57 AM #16Ray
'09 Avalanche LTZ - Black
'05 Envoy XL (sold)
08-26-2012, 12:11 PM #17
08-26-2012, 01:55 PM #18
08-26-2012, 06:53 PM #19
And, the same hitch will be used with, or without the air bags.
08-27-2012, 10:11 AM #20
By alkaspeltzar in forum Chevy Silverado Forum (GMC Sierra)Replies: 4Last: 07-16-2012, 04:15 PM
By ChevyBoy2009 in forum Lifted & Offroad SuspensionReplies: 10Last: 05-17-2011, 11:11 PM
By tigersdl65 in forum General Chevy & GM Tech QuestionsReplies: 2Last: 11-07-2010, 11:23 PM
By rfoster813 in forum Lifted & Offroad SuspensionReplies: 5Last: 05-14-2009, 03:31 AM
By grantahoe in forum Chevy Tahoe Forum (GMC Yukon, Cadillac Escalade)Replies: 2Last: 01-14-2008, 01:57 AM
Tags for this Thread