GM Truck Club
THE PREMIER CHEVY TRUCK & SUV FORUM
Founded in 2004 ~ We're the #1 Chevy Truck & SUV Forum.
Silverado & Sierra | Tahoe & Yukon | Suburban & Yukon XL | SUV & CROSSOVER
Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15
  1. #11

    Default

    Quote Originally Posted by reggiecab2000 View Post
    well today i finally had time to swap in the new set of LS1 fans, hopefully they last this time..... same brand VDO.
    Did they replace them under warranty?

    1995 Silverado 4x4
    6" BDS Suspension Lift-3" Body Lift-Add A Leaf in rear -Trailmaster SSV Shocks-Duel Steering Stabilizer Kit -AirAid Cold air intake-
    4.56 Gears with Detroit Auburn Locker-Pro-Comp Traction Bars with duel shocks-Aluminum Skid Plate Kit-38.5" x 16.5" Mickey Thompson Baja Claws-Constant Dropping fuel gauge

    2005 Yukon XL Jet Power Programmer, Bilstein Shocks, Bilstein rear springs, Helwig Anti-sway bars, EGR Window Visors, EGR Hood Shield, Denali Headlights, Headlight harness upgrade, GE NightHawk Bulbs, White Night Rear lighting system, Russell Braided SS brake lines, PowerStop Brake pads, PowerStop cross drilled and Slotted Rotors, http://www.gmtruckclub.com/forum/sho...5-GMC-Yukon-XL
    2002 Silverado ext cab 2wd (Sold)
    2003 Yukon XL (Totaled)

  2. #12

    Default

    Quote Originally Posted by Pikey View Post
    Did they replace them under warranty?
    no since i bought it off amazon, they dont offer any replacement warranty, i see tha if i bought the same item from advanceautoparts, or oreilleyauto, they have a 1-year replacement warranty, but initial price for the same fan is about $270.00
    2000 Chevrolet Silverado

    Powertrain:
    4.3L V6, 4L60E, 2WD, Single Cab
    Performance:
    Airaid CAI
    Poweraid TB Spacer
    Flowmaster 10-series exhaust (dumped)
    BLACKBEAR TUNED!!!
    Edge CS insight monitor
    4.10 gears
    Limited-slip differential
    LS-1 Dual Electric fans
    Corvette tranny servo swap

    Audio:
    Head Unit: Alpine
    Speakers: Alpine SPR-60C 6.5" component set, 4X6 Infinity Kappas
    Subs: 2-12" Kicker CVT's
    Amps: Alpine-M1000 (subs), Alpine MRX-F65 (Speakers)


    Tires/Wheels:
    305/70R16 NITTO Terra Grapplers
    16" PROCOMP 7089's
    Suspension:
    2" leveling kit
    3" Fabtech Spindle Lift Kit
    Front/Rear-Bilstein 5100 shocks

    Lighting:
    FRONT
    35W HID Low Beams
    RECON LED smoked roof cab lights
    REAR
    HELLA LED taillights and 3rd brakelight
    HELLA FF-75 Aux. Reverse Lamps
    RIGID dually D2, flush mount, wide beam
    Accessories:
    Hawk HPS Brake pads
    Russell braided steel brake lines
    Powerstop-red powdercoated brake calipers
    Powerslot Cryo brake rotors
    EGR in-channel window visors

  3. #13

    Default

    Ok so I'm considering doing this mod on my 95 2500 4x4 I already have a fan setup from my 96 trans am part out. My question is would this be a hard wire switch setup. Pretty sure my good ole TBI 350 has much tuning involved.
    2003 Tahoe 4x4 blacked out with 5.3L and small lift.
    1995 K2500 Single cab 3" body lift...on its way to the grave soon.

  4. #14

    Default

    Quote Originally Posted by Smoke Em All View Post
    Ok so I'm considering doing this mod on my 95 2500 4x4 I already have a fan setup from my 96 trans am part out. My question is would this be a hard wire switch setup. Pretty sure my good ole TBI 350 has much tuning involved.
    Wiring in fans is extremely simple, basically all you're going to need is a 40amp relay, some terminals, and some decent sized wire (i've always used 14AWG).

    "If you're not living life on the edge, You're taking up too much space"

    "Truck Norris"
    - 2008 TX Edition Silverado
    - McGaughy's 4/5 Drop Kit
    - Apline Type R 10s & Amp
    - Pioneer 6 Disc Touchscreen Deck
    - Nightmare Breed Motorsports custom tune
    - Custom 3" dual exhaust through x-pipe dumped at axle
    - Airaid CAI
    - Badges and molding removed, roll pan, Truxedo roll-up cover (compliments of GMTC!), 3pc billet grille, factory fogs upgrade
    "Kristine" - 1991 Nissan 240sx
    - Cut to pieces, LS build pending

  5. Likes reggiecab2000 liked this post
  6. #15

    Default

    Quote Originally Posted by 08_rado_rocker View Post
    Wiring in fans is extremely simple, basically all you're going to need is a 40amp relay, some terminals, and some decent sized wire (i've always used 14AWG).
    Thanks
    Do you know where I could find a diagram for my my model truck so I know where they all go?

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Head swap, Cam swap, cheep mods, and Torque specs and more
    By darnie1987 in forum How-to Guides
    Replies: 3
    Last: 07-16-2013, 02:33 AM
  2. LED cluster swap. Finally.
    By Cheez in forum Lighting Discussion
    Replies: 8
    Last: 07-15-2013, 10:31 AM
  3. 85 Sub 1 ton 454 engine swap and tailgate to barn door swap.
    By RallySTX in forum Chevy Suburban Forum (GMC Yukon XL)
    Replies: 1
    Last: 05-19-2012, 09:26 PM
  4. rear end swap or gear swap
    By rmagni in forum GM Powertrain
    Replies: 4
    Last: 08-18-2009, 07:42 PM
  5. Finally..
    By Chevyman224 in forum Photo & Video Gallery
    Replies: 10
    Last: 04-02-2009, 11:44 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •