Results 1 to 8 of 8
Thread: Chevrolet Performance 5.3 swap
09-12-2012, 12:12 AM #1
Chevrolet Performance 5.3 swap
So after a bit of deliberation, I have decided that one day once I'm in the Navy and it comes time for a new truck, I'm not going to get one. Instead I'm thinking about doing what @Tachyon did. Buying a new performance replacement engine and going that whole route.
After a bit of searching, I came across a Chevrolet Performance 5.3/327 High Output. Same as a 383 is for a 350; drop in replacement essentially. I'd probably do this myself using MOST accsessories off of my old engine and some help from some Navy buddies probably unless I can get a professional to do it while I'm away. Eventually I plan on lifting the truck 3 inches and putting on 33s and regearing and this is probably when I'll do it. Sure will be alot cheaper than a new truck.
If I do this I plan on adding a air intake, a "custom" exhaust system to help it breathe better and maybe even a tune to squeeze a few extra horses out. Not sure yet if I'll rebuild my 4L60 or get a new 4L80 trans to stick behind it.
Anyone know anything on those engines? I have provided a link to the engine from JEGS. Sure does look pretty.
If at first you don't succeed, chances are, you are using too small of a cheater bar
1999 GMC Sierra SLT Z71 | 5.3 Vortec | Spectre Cold Air Intake | TransDapt TBS | Hypertech 30005 Tune | 2005 Chevy Tails | Denali headlights | AWS Bug Shield | 265/75/16 Mastercraft Courser A/T | "Ghetto" painted tailgate | Boss HD Speakers | 2005 Overhead Console | Dual Thrush Turbo Mufflers
Bigger Amp Alternator | Electric Fans | Oil/Trans Fluid cooler | Re-done exhaust | Paint | Interior Restoration/upgrade with newer model stuff | Window Visors (In channel) | Tint | Low-Profile Tool Box | LEDs throughout stock cab locations | And whatever is spurr of the moment
US Navy Sailor :sign0011:
09-12-2012, 06:36 AM #2
The good thing about your choice is that once in the Navy you will have access to what they call a hobby shop. The hobby shop is where you can go work on your truck and have the use of the lift and some tools. Most also have a guy that works there to assist you should you need help. The one at MCAS Cherry Point usually had a few guys that were always up to help pop and swap motors. So where evere you get stationed you may get lucky and have people that would like to helpout.
2011 GMC Sierra SLE - 5.3 - 4X4 - Z71 - King Shock Level Kit - Body Color GMC grill emblem - 2 Tone Engine Cover, Rad Cover and Battery Box - Volant CAI - Tru Cool 40K tranny cooler - Sylvania ZXE bulbs Hi/Low -TriFold Hard Tonneau Cover- CoverCraft Seat Covers - Diablo inTune - GoRecon LED under rail lights - GoRecon LED White Lightning Tailgate Light Bar - Windows tinted to 45%- Kenwood DNX6990 - JL Audio C5-650 &650X- JL Audio Amp- Interco Truxus M/T 33x12.50x18
09-12-2012, 10:56 AM #32006 Vortec Max 1500
-Custom Tune (389HP 440 Ft/lbs Trq - Dyno'd) | Volant CAI | Magnaflow Dual-in/out Exhaust w/3" stainless pipe tips | Fully Built Transmission w/ Red Eagle Clutches & Kolene Steels w/ Corvette Servos and Stage2 Shift Kit | 35K Tranny Cooler | Mobil 1 | Royal Purple Rear Diff
-Spray-in Bed Liner
-Premium Sound w/lifetime Satellite Radio | Leather | Sunroof | Heated Seats
-Limbstriping from USING the truck (those are badges of honor)
09-12-2012, 01:15 PM #4
- Join Date
- Mar 2007
- Grand Prairie, Texas
- Blog Entries
Some Auto Hobby Shops are set up so the vendors will pick up and deliver parts to the hobby shop during normal working hours.
Every one of them I've ever been to has lifts and cherry pickers along with bench's, drill presses, and many other tools all available for you to use at the Hobby shop.
Just one more of your little known Military benefits provided by the MWR.
09-12-2012, 03:19 PM #5
See I probably wouldn't have know about the Auto Hobby Shops if someone would have told me.
09-13-2012, 03:37 AM #6
Sounds like a plan. Here's a few thoughts in case you are interested in my two cents.
- Have you looked at the GMPP versions? I was going to go with a third party vendor and get some friends to help with the swap, but after considering everything, I put off the whole thing for a year and saved up to have it done at the dealer. The primary reasons for this were a) warranty through any GM dealer b) emissions compliance
- Regarding transmissions, if you have a 4L60E now, I'd upgrade because once you start upgrading, it's hard to stop adding power. The 4L60E is a little weak so you don't have a lot of room to grow. GMPP has a 4L70E made for rodders and swappers. More power handling and available stand alone controller to make it work with anything. And again, it comes with a warranty.
- I absolutely recommend going with a full stem to stern upgrade plan. A hot engine that can't breathe is a waste of your hard earned money. I'd spec, price, and plan for a Cold-air intake kit, shorty headers, and exhaust system.
- Definitely do the headers at the time of the engine swap, even if that means putting it off a little longer to save the money. It's much easier to do at the same time as the engine swap and will let the engine breathe better from the get go. Shorty headers let you mate to the factory exhaust which lets you upgrade that later. It also lets you purchase an off the shelf, custom fit manifold back exhaust system from someone like Magnaflow instead of having to pay more for an untested and unoptimized custom fit exhaust system.
- Do your research. Google is free. Mistakes are expensive.
- If you're lucky, there's a shop in your area that's got a dyno and is good with EFI-Live. That would be my final step in this stage of the upgrade.
- Don't underestimate the value of a dealer warranty.
Good luck and thanks for serving!The Real, Original Tachyon.
Accept No substitutes!
- 99 K2500 Suburban with GMPP HT383E Engine, Hypertech Max Energy programmer, JBA 1832S-2 headers, Magnaflow cats and exhaust, K&N Cold Air Intake, Tahoe Sport Grill Swap, Go Industries Rancher Grill Guard, PIAA Driving Lights, Anzio Headlights
- 88 K1500 Suburban with Targetmaster 350 and built TH700R4 - Gone but not forgotten!
09-13-2012, 10:42 AM #7
- Join Date
- Mar 2007
- Grand Prairie, Texas
- Blog Entries
But yea adding all the extra parts on at installation time makes a lot of sense and should save time and money, the worst part is you might have to wait a little longer to come up with the funds but it will save in the end.
09-13-2012, 12:38 PM #8
another option on the tranny is to gut your 4L60, and rebuild it with 4L8o internals, should save you a few $$$.
anther option would be a LQ9 swap for a escalade. i believe the excalades came witha 4L80. if you could find a lower mileage one with a good engine and tranny, it should all just bolt up. I think anyhow. just a few thoughts for ya.
2011 GMC Sierra SLE 5.3 Z71 4X4 Stealth Gray Metallic
Tow mirrors - Diablew Tuned - Flowmaster Regular 40 - Ready Lift 2.5' lift - BFG LT A/T K/Os - Carr Light Wing - TruckLite LED lights - Optima Red Top - 50% Front Window Tint - Line-X bedliner - Aidaid MIT - Tekonsha P2 - ARS Billet Grill
By darnie1987 in forum How-to GuidesReplies: 3Last Post: 07-16-2013, 03:33 AM
By RallySTX in forum Chevy Suburban Forum (GMC Yukon XL)Replies: 1Last Post: 05-19-2012, 10:26 PM
By Chevy Man NC in forum GM PowertrainReplies: 3Last Post: 10-28-2011, 07:11 PM
By Rockstarrchevy81 in forum Performance & FuelReplies: 4Last Post: 05-20-2011, 06:06 PM
By mechalloy in forum Performance & FuelReplies: 2Last Post: 06-04-2009, 06:47 PM