1. Welcome To GMTruckClub.com!

    The #1 Chevy Truck Forum Online
    Online since 2004, we are the #1 Chevy Truck & SUV forum and user community. If you have any questions about your Chevy or GMC Truck, SUV or Crossover, or just want to connect with other GM owners and enthusiasts around the world, you've found the best place on the internet to do that.

    Join Today ~ It's Free
    Registering is Free and Easy! Hope to see you on the forums soon!

What have u done to ur GM truck today?

Discussion in 'Chevy Truck Talk & GM News' started by devilsalmostfree, Feb 28, 2010.

Thread Status:
Not open for further replies.
  1. reggiecab2000

    reggiecab2000 Rockstar 4 Years 500 Posts

    broke off a whole strand of rotted 3/8" split loom tubing that protects my ABS cable across my front end, and put new tubing on it
  2. jsmith4816

    jsmith4816 Member 2 Years 100 Posts

    Drove it to work. Tomorrow will give her a bath and try and find this screeching I have coming from my drivers side area.
  3. PantheraUncia

    PantheraUncia Active Member 2 Years 1000 Posts

    Ordered 2 Door blend actuators of the 3 that are needed in the truck for the HVAC to work properly
  4. darkness-lies-

    darkness-lies- Member 2 Years 100 Posts

    Does it get worse while turning?
  5. jsmith4816

    jsmith4816 Member 2 Years 100 Posts

    Yeah, and when I hit a bump I hear it too.
  6. darkness-lies-

    darkness-lies- Member 2 Years 100 Posts

    I know when my hub assembly went out both side different times if made noise worse when i turned. Not sure if they changed a lot from your model to mine or not.
  7. Conlan Rose

    Conlan Rose Active Member 2 Years 1000 Posts

    Me and my dad brought her to VT for the weekend because we bought a new fridge. God was Tahoe happy on the open road. Tomorrow will be redoing aux wiring.

    - - - Updated - - -

    Had a good day working was super successful. I installed a new aux switch on the dash and began to rewire my aux wiring. I just finished the vehicle side connector just need to re wire the box, install and hook up the always on switch for the back light. Will need to upgrade ground current wire is only 14 gauge will need at least 10.
    2012-12-15_17-41-36_903.jpg 2012-12-15_17-41-49_806.jpg 2012-12-15_17-41-56_713.jpg 2012-12-15_17-42-06_681.jpg 2012-12-15_18-32-18_208.jpg 2012-12-15_18-32-29_443.jpg 2012-12-15_18-32-34_16.jpg 2012-12-15_18-32-40_198.jpg 2012-12-15_18-33-07_904.jpg 2012-12-15_18-43-29_834.jpg 2012-12-15_18-43-39_442.jpg
    Vehicle side connector, I went over board with the heat shrink.
    2012-12-15_17-41-42_412.jpg 2012-12-15_20-40-00_360.jpg 2012-12-15_21-01-25_852.jpg 2012-12-15_21-01-31_151.jpg 2012-12-15_21-01-37_70.jpg
    2012-12-15_21-47-11_32.jpg
    Last edited: Dec 15, 2012
  8. SurrealOne

    SurrealOne Former Member ROTM Winner 1000 Posts

    I ordered a blank, single gauge panel for the overhead console, today.
  9. Conlan Rose

    Conlan Rose Active Member 2 Years 1000 Posts

    Today i continued rewiring the aux wiring, I attached the switch lead to the rear relay, fixed the mixed up trailer wires, and prepped the aux driving light wires. I got to the 80% done mark on the wiring and ran out of 16-14 butt connectors... Now I just need to wire up the box side connector, re-install the power leads, attach the new ground, and hook up the accessories to the box.

    2012-12-16_12-41-25_514.jpg 2012-12-16_10-24-30_709.jpg 2012-12-16_10-24-38_152.jpg 2012-12-16_12-40-52_663.jpg
    2012-12-16_12-40-43_143.jpg 2012-12-16_12-40-37_313.jpg

    - - - Updated - - -

    Switch is not working as planned.... I may have to figure out where I messed up.
  10. McClintoc

    McClintoc ɹoʇɐɹǝpoɯ Staff Member 2 Years 1000 Posts Platinum Contributor

Thread Status:
Not open for further replies.

Share This Page