GM Truck Club Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-10 of 10 Results
  1. GM Electrical Tech
    Hello I am currently ls swapping my 79 ford bronco but I am currently held up trying to figure out engine and transmission wiring. I am using a drivetrain from a 2003 Chevy suburban 1500 4x4. When the engine was pulled alot of the wiring was cut so I am currently trying to figure out exactly how...
  2. Chevy Suburban Forum (GMC Yukon XL)
    I was wondering if anybody could help me figure out what to do with my current 350 that I believe has a dropped valve, im not sure if I should find a GM engine builder and bore it out to a 383 or if I should swap it out for an LQ9 or something newer. I havent been able to find any GM engine...
  3. General Chevy & GM Tech Questions
    Hello,I’m putting a 02 6.0 out of a Denali into a 90 Silverado 1500 2wd with a 5spd I’m wanting to keep the 5spd I’m not real sure what model the trans is just a basic 2wd 1500 truck, my question is what flywheel,clutch assembly,pilot bearing,etc do I need to get to make it all work thanks for...
  4. GM Powertrain
    howdy folks, the tired 4.8 and 4l60 in my 03 sierra is looking mighty fine for a drivetrain swap, what does it realistically take to do a gen 4 swap with a 6l80/6l90 and to be able to have someone who doesn't know anything about the truck feel like its a regular truck? I'm so sick and tired of...
  5. General Chevy & GM Tech Questions
    Hello im having a little trouble on what wiring harness i need to get. im 19yrs old and i just pulled my first motor its a 5.3 ls out of a 2001 suburban which im swapping into my 1994 1500 4x4. it has a 4l60 and when i look online all they have is 4l60e wiring harness its probably a stupid...
  6. Chevy Truck Talk & GM News
    Hello im having a little trouble on what wiring harness i need to get. im 19yrs old and i just pulled my first motor its a 5.3 ls out of a 2001 suburban which im swapping into my 1994 1500 4x4. it has a 4l60 and when i look online all they have is 4l60e wiring harness its probably a stupid...
  7. GM Powertrain
    Needing some help and don't know where else to turn to. I put a 2000 5.3 and 4L60 from a suburban in Jeep Comanche. I used a NP241 with a SYE. I purchased Dakota Digtial SEN-01-4280 and SGI-100BT to get the VSS signal to computer. I have hooked up per instructions in manual and have had no...
  8. Chevy Suburban Forum (GMC Yukon XL)
    I'm taking the 6.0 LQ9 from a 2007 Silverado and transplanting it into my '99 K1500 Suburban, there's not a whole lot of info on exactly everything I need and I've got a general idea for parts needed but I'm not sure if I've got everything. I also need help on how to route the air intake as I...
  9. Chevy C/K Truck Forum
    I have a 1996 tahoe 2 door 4wheel drive and i wanna swap a 6.2 from a escalde in it were are some places or websites i would be able to get a plug and play harness or what i would have to do to get it all wired up and ready to run im sorta cluless on swapping ls's
  10. Chevy C/K Truck Forum
    Hello everybody, I have done a lot of research on how i'm going to make my LS1 fit into my truck. It's a 1994 k1500 regular cab short bed. The only thing I am having trouble nailing down is if my 4L60E (original to he truck) is going to bolt up to the LS engine or if I will need an...
1-10 of 10 Results
Top